MicroFit Application Form

This form is used to request the connection of a generation facility of 10 kW or smaller to the Distributor’s distribution system. Please ensure that you have read and agreed to the terms before proceeding

"*" indicates required fields

1.0 ELIGIBILITY

1.1 The Customer agrees that its generation connection shall be subject to all applicable laws and regulations, including but not limited to the Distribution System Code and the Ontario Electrical Safety Code.

1.2 The connection is bound by the terms and conditions of the Distributor’s Conditions of Service as amended from time-to-time as well having been filed with the OEB, available upon request.

2.0 TECHNICAL REQUIREMENTS

2.1 The Customer represents and warrants that they have installed, or will install prior to the connection of the generation facility, an isolation device satisfying Section 84 of the Ontario Electrical Safety Code and in a location satisfactory to the Distributor. The Customer shall allow the Distributor’s staff access to and operation of this as required for the maintenance and repair of the distribution system.

2.2 The Customer agrees to perform regular scheduled maintenance to the generation facility as outlined by the equipment manufacturer in order to assure that connection devices, protection systems, and control systems are maintained in good working order and in compliance with all applicable laws.

2.3 The Customer agrees that during a power outage on the Distributor system, the generation facility will shut down, unless special transfer and isolating capabilities are installed on the generation facility. Further, the Customer agrees to the automatic disconnection of its generation facility from the Distributor’s distribution system, as per the generator protective relay settings provided in Table 1 and 2 of this Agreement, in the event of a power outage on the Distributor’s distribution system or any abnormal operation of the Distributor’s distribution system.

2.4 The Customer covenants and agrees that the design, installation, maintenance, and operation of the generation facility are conducted in a manner that ensures the safety and security of both the generation facility and the Distributor’s distribution system.

2.5 Due to the Distributor’s obligation to maintain the safety and reliability of its distribution system, the Customer acknowledges and agrees that, in the event the Distributor determines that the generation facility (i) causes damage to; and/or (ii) is producing adverse effects affecting other distribution system customers or the Distributor’s assets, the Customer will disconnect generation facility immediately from the distribution system upon direction from the Distributor and correct the problem at the Customer’s own expense prior to reconnection.

3.0 LIABILITIES

3.1 The Customer and the Distributor will indemnify and save each other harmless for all damages and/or adverse effects resulting from either party’s negligence or willful misconduct in the connection and operation of the generation facility or the Distributor’s distribution system.

3.2 Both parties shall not be liable to each other under any circumstances whatsoever for any loss of profits or revenues, business interruptions losses, loss of contract or loss of goodwill, or for any indirect, consequential, incidental or special damages, including but not limited to punitive or exemplary damages, whether any of the said liability, loss or damages arise in contract, tort or otherwise.

4.0 COMPENSATION AND BILLING

4.1 If the Customer is not an embedded retail generator, they agree that, subject to any applicable law: a) the Distributor will not pay for any excess generation that results in a net delivery to the Distributor between meter reads; and b )there will be no carryover of excess generation from one billing period to the next unless the Customer is, at the relevant time, a net metered generator (as defined in section 6.7.1 of the Distribution System Code).

4.2 If the Customer is an embedded retail generator selling output from the generation facility to the Independent Electricity System Operator under contract, the Customer agrees that the Distributor will pay for generation in accordance with the Retail Settlement Code.

4.3 If the Customer is an embedded retail generator delivering and selling output to the Distributor, the Distributor will pay for generation in accordance with the Retail Settlement Code.

5.0 TERMINATION

5.1The Customer has right to terminate this agreement at any time, and that by doing so the generation facility shall be disconnected with notification provided to the Distributor.

6.0 ASSIGNMENT

6.1 The Customer may assign their rights and obligations under this Agreement with the consent of the Distributor, which shall not withhold its consent unreasonably. The Distributor shall have the right to assign its rights and obligations under this Agreement without the consent of the Customer.

7.0 AGREEMENT

I understand, accept and agree to comply with and be bound by the above terms and conditions governing the connection of my generation facility to the Distributor’s distribution system.

I/We accept the terms and conditions above*

Yes

Type of Service*

Residential

Business

Name (Name should match exactly as it will be registered at the IESO)*

First Name Last Name

Business Name (Name should match exactly as it will be registered at the IESO)*

Phone Number*

Email*

Date of Birth*

Please select your form of government-issued identification*

Ontario Driver’s License Number

Ontario Photo Card

Out of Province Driver’s License Number

Identification Number*

Ontario Driver’s License format: X9999-99999-99999 Ontario Photo Card Identification format: 999-XX99-999

Existing Enova Account Number (If Applicable)

HST# (If Applicable)

Address-Generation Service Location*

Unit Number (if applicable) Street Number and Street Name City Postal Code

Are there additional account holders associated with this account?*

Yes

Contact Person

First Name

Last Name

Phone

Secondary Contact (If Applicable)

Name (Name should match exactly as it will be registered at the IESO)*

First Name Last Name

Identification Number*

Ontario Driver’s License format: X9999-99999-99999 Ontario Photo Card Identification format: 999-XX99-999

Date of Birth*

Phone number (if different from above)

Relationship Type*

Mailing Address

Is the mailing address for billing purposes different from the service address

Yes

Address*

Unit Number (If Applicable) Street Number and Street Name City State / Province / Region ZIP / Postal Code Country

Additional Information

I agree to the Rules and Regulations*

Yes

Name & Title of Authorized Signatory*

Signature*

Today's Date

CAPTCHA

This form must be submitted concurrently with the MicroFIT Pre-Authorized Payment Application Form. [link]

Upon receipt of both forms, Enova will process the submissions and provide your account number via email for submission to the IESO.

Before you submit, please take a moment to review and verify that all information provided on this form is correct.

MicroFit Application Form

Contact Person

Secondary Contact (If Applicable)

Mailing Address

Contact Us

Quick Links

Login to My Account